PIC, EEprom and MCU Programmer




In order to program PICs, EEproms and other MCUs, they have to be connected to MAKInterface. There are several opportunities for establishing the connection:

IC-Test-Clip (For serial EEproms and PIC16X84. Available is a DIP and SMD version)
Probe-IT Clips

The IC-Testclips and Probe-IT clips are directly connected to MAKInterface, using a cable and a 10 pole connector.

00115Art. 00115
59.00 EUR
88.50 USD
MAKInterface Pro LP with build-in crystal 3.579 MHz and exchangeable crystal 6.0 MHz
Pcs.

 



The advantage of the IC-Testclips and Probe-IT clips is, that in many cases serial EEproms and PIC16F84 can be can programmed in circuit, without desoldering. Whether this will be possible or not, depends on the circuit design, where the EEprom is located.

Pinouts for various devices are given in the Support menu. In the Support menu also the Jumper Settings of MAKInterface Pro for PonyProg and IC-Prog are described.




IC-Test-Clips

The IC-Testclips are recommended for programming of greater quantities of unified IC types (I2C = 24C16, 24C65, ...) because the connection of the IC is established very quick and easy by attaching over the IC. A change of the wires is only needed in case the IC type changes as for example from I2C to SPI, Microwire, PIC, Atmel AVR, etc.

After the IC Tetclip is connected by a cable to MAKInterface, it has just to be attached over the IC

It is not important whether the IC is on a PCB or standalone


DIP IC Testclip 16 pole

Goldplated, low-cost IC-testclip with 2*8=16 pole. This testclip is in most cases not suitable to be used for In-Circuit programming, because it is too wide. But it is a good solution for programming of desoldered PIC16F84 and serial EEproms.

00720Art. 00720
6.90 EUR
10.35 USD
DIP IC-Testclip LowCost, 16 pole. This article is at present out of stock.
 

 

Out of stock





DIP IC Testclip 8 pole

Goldplated 0,25mµ. Easy attachment with a narrow nose shape for working on high-density PC-boards. Fits onto ICs with only 2.5mm between leads and adjacent components.

Proven contact wiping action for optimum reliability. Flat "Duck-Bill" contacts won't roll off narrow DIP leads. Knife-Edge contacts for elder and greasy DIP leads. These contacts will cut though the coating.

The open nose design permits probe access at DIP leads.

00722Art. 00722
12.90 EUR
19.35 USD
DIP IC-Testclip HighQuality, 8 pole
Pcs.

 

00730Art. 00730
9.90 EUR
14.85 USD
Connection Cable for MAKInterface with articles 00722, 00724, 00728 and 00505 (for smartcards, which do not posses a pinout according ISO 7816)
Pcs.

 





SMD IC Testclip 8 pole

With this small goldplated testclip even SOICs having a distance of only 0.64mm can be tested.

This testclip is specailly designed for small outline ICs.

Although the distance between pins the end of the IC is only 1.27mm, a distance of 2.54mm between pins is reached at the tap end.

The standard 0.64mm square pins enable a easy attaching of the respective connectors or "wire wrapping"

00724Art. 00724
24.00 EUR
36.00 USD
SOIC IC-Testclip HighQuality, 8 pole. This article is at present out of stock.
 

 

Out of stock

00730Art. 00730
9.90 EUR
14.85 USD
Connection Cable for MAKInterface with articles 00722, 00724, 00728 and 00505 (for smartcards, which do not posses a pinout according ISO 7816)
Pcs.

 




Probe-IT Clip Sets

These plunger-actuated clips make test connections to individual component leads faster and easier. Simply by pressing the cap of the Probe-IT the contact hook is extended. After placing it on the component lead and then releasing, contact will be established. Shortenings are prevented because the contact hook is always sheated in the nylon body of the Probe-IT clip.

DIP-Plunger-Clip

In case, only DIP-elements will be programmed, we do recommend the DIP-Plunger-Clip.

00727Art. 00727
14.90 EUR
22.35 USD
DIP-Plunger-Clip Set-Actuated-Clips set for programming of seriall EEproms and microprocessors in DIP-format
Pcs.

 


SMD-Plunger-Clip Set

The SMD-Plunger-Clip Set provides highest flexibility for establishing connections to almost any IC housing: DIP, SMD, PLCC, ... ICs with various dimensions and number of pins can be connected - 8 pole I2C EEprom 24C16 or 40 pole AT90S8515 - the connection is established very quick and easy.

In the normal position the two hooks are inside and do establish a contact to the pin

By pressing the cap of the SMD-Plunger-Clip the contact hook is extended

On any SMD-Plunger-Clip two cables can be connected

In case of a normal connection, only one cable is connected.

When using halfduplex protokolls (I2C, PIC, ...) two cables can be used in order to connect Data-In und Data-Out channels. So it is not neccessary to connect two clips to one pin.

The SMD-Plunger-Clip enables the connection of the pins to MAKInterface for a great quantity of various IC housings.

DIP ICs can be connected to the lower end of the pin ...

... or to the top end of the pin, in case the IC is placed on a PCB

Pins of SMD ICs can also be accessed without problems

The hooks of the clips are so thin that shortening of two neighboured pins is almost impossible

Even PLCC ICs can be connected with IC testclips

Also two neighboured contacts, as necessary in case of 68HC11


00728Art. 00728
34.90 EUR
52.35 USD
SMD-Plunger-Clip Set - actuated clips set (7 pieces) for programming of serial EEproms and microprocessors in im DIP/SMD/PLCC-format
Pcs.

 

00730Art. 00730
9.90 EUR
14.85 USD
Connection Cable for MAKInterface with articles 00722, 00724, 00728 and 00505 (for smartcards, which do not posses a pinout according ISO 7816)
Pcs.

 





Connection cable

The connection cable is used to connect the DIP and SMD Testclips with MAKInterface. On every wire there is a female connector which is easy attached on the standard 0.64mm square pins.

On the wires 2 (RX) and 5 (CTS) is a additional standard 0.64mm square pin, so also halfduplex connections (required for I2C) can be established.


00730Art. 00730
9.90 EUR
14.85 USD
Connection Cable for MAKInterface with articles 00722, 00724, 00728 and 00505 (for smartcards, which do not posses a pinout according ISO 7816)
Pcs.

 





Following a table with recommended Testclips and Probe-IT Clip Sets for programming of various devices:


Device Article-Nr. 00720/00722
DIP IC-Testclip
suitable for programming of following devices
Article-Nr. 00724
SOIC IC-Testclip
suitable for programming of following devices
Article-Nr. 00727
DIP-Plunger-Clip set
suitable for programming of following devices
Article-Nr. 00728
SMD-Plunger-Clip Set
suitable for programming of following devices
I2C - 24Cxx,
SDA, SDE, PCF
DIPSOICDIPDIP, SOIC
Microwire 93CxxDIPSOICDIPDIP, SOIC
SPI-25xxx,95xxxDIPSOICDIPDIP, SOIC
4-wire - 59CxxDIPSOICDIPDIP, SOIC
IM-Bus
NVM3060
DIPSOICDIPDIP, SOIC
NVRAM
X24C44/45
DIPSOICDIPDIP, SOIC
CXK10xx
TC8910x
DIPSOIC8DIPDIP, SOIC
AT90TinyXX
AT902323/43
DIPSOICDIPDIP, SOIC
AT89S8252
AT89S53
------DIPDIP, SOIC, PLCC
AT90S1200
AT90S2313
AT90S2333
AT90S4414
AT90S4433
AT90S4434
AT90S8515
AT90S8535
ATmega83
ATmega161
ATmega163
------DIPDIP, SOIC, PLCC
PIC12C508/9
PIC12C671/2
PIC16C505
PIC16C554/6/8
PIC16C61
PIC16C620/1/2
PIC16C71
PIC16C710/1
PIC16C84/F84
DIPSOICDIPDIP, SOIC, PLCC
PIC16C63/4/5/6/7
PIC15C641/2
PIC16C661/2
PIC16C773/4
------DIPDIP, SOIC, PLCC
Code Hopping
HCSxxx
DIPSOICDIPDIP, SOIC
Atmel Dataflash
45DBxxx
------DIPDIP, SOIC, PLCC
Motorola (*)
68HC05/705
------DIPDIP, SOIC, PLCC
Motorola
68HC11/711
------DIPDIP, SOIC, PLCC
(*) Requires 12V external power supply for programming